STIEBEL ELTRON WPL 15 IKS-2 Скачать руководство пользователя страница 29

Страница: 29 / 76

INSTaLLaTION

appliance installation

www.stiebel-eltron.com

WPL 15 IKS | WPL 25 IK |

00000

1 Aluminium-lined mineral fibre shell

2 Thermally insulated refrigerant lines

- In addition to the thermal insulation, use aluminium-lined

mineral fibre shells (min. thickness 20 mm) to minimise ge-

neral and flow noise.

- Use suitable anti-vibration pipe clips to secure refrigerant

lines.

- Secure the pipe clips on the outside over the alumini-

um-lined mineral fibre shells

- Never install pipe clips near pipe bends.

- Never secure refrigerant lines to internal walls that border

living areas or bedrooms.

- Ensure that no strain can be placed on the soldered

connections.

Sample installation

�0

3�

�1

1 Pipe clips

10.5.3 Connecting refrigerant lines

Material damage

Commissioning below+5 °C is only permissible if the

pre-installed refrigerant lines are perfectly sealed and

their ends point downwards, thereby preventing the in-

gress of dirt and water. Purge the refrigerant lines tho-

roughly with nitrogen.

Remove the protective caps from the connection pipes using

a suitable tool.

External unit

Note

The external unit is filled with nitrogen. When the pro-

tective caps are removed, the nitrogen escapes.

�0

3�

�18

1 Refrigerant, liquid line

2 Refrigerant suction gas line

Internal unit

�0

3�

�1

829

1 Refrigerant, liquid line

2 Refrigerant suction gas line

Use the female soldering connections contained in the stan-

dard delivery to connect the refrigerant lines to the units.

Female soldering connections are supplied in imperial and

metric dimensions.

Ensure that thermal insulation is not damaged during sol-

dering work and that neither moisture nor dirt is allowed to

penetrate the refrigerant circuit.

Make sure soldered joints are tight.

Содержание WPL 15 IKS-2













































































Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPL 15 IKS-2, Эксплуатация и установка

Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды