STIEBEL ELTRON WPL 15 IKS-2 Скачать руководство пользователя страница 22

Страница: 22 / 76

INSTaLLaTION

Preparations

| WPL 15 IKS | WPL 25 IK

www.stiebel-eltron.com

9.1.2 Minimum clearances

≥500

≥150

≥300

≥1500

00000

Maintain the minimum clearances to ensure trouble-free

operation of the appliance and facilitate maintenance work.

9.2 External unit

The appliance is designed for siting in front of a wall. Observe

the minimum clearances. If the appliance is installed in an open

space or on a roof, protect the air intake side by erecting a wall

to shield it against the wind.

00000

The substrate at the installation site must be horizontal, level,

solid and permanent.

9.2.1 Sound emissions

The appliance is louder on the air intake and air discharge sides

than on the two enclosed sides. Observe the following information

when selecting the installation location.

Note

For details regarding the sound power level, see chapter

"Specification / Data table".

- Lawn areas and shrubs help reduce the spread of noise.

- Sound propagation can also be reduced by installing closely

spaced palisade fencing around the appliance.

Ensure that the air intake direction is the same as the main

wind direction. Air should not be drawn in against the wind.

Ensure that the air intake and air discharge are never di-

rected towards noise-sensitive rooms of the house, e.g. be-

drooms, or neighbouring houses.

Avoid installation on large, echoing floor areas, e.g. tiled

floors.

Avoid installation between reflective building walls. Reflec-

ting building walls can increase the sound level.

Minimum clearances

�0

0�

�0

Do not install the appliance in a recess. Two sides of the ap-

pliance must be exposed.

≥250

≥2000

≥500

≥800

00000

Maintain the minimum clearances to ensure trouble-free

operation of the appliance and facilitate maintenance work.

Содержание WPL 15 IKS-2













































































Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPL 15 IKS-2, Эксплуатация и установка

Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды