STIEBEL ELTRON WPL 15 IKS-2 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 76

background image

INSTaLLaTION

Troubleshooting

www.stiebel-eltron.com

WPL 15 IKS | WPL 25 IK |

59

Fault list for refrigerant circuit faults

fault display

Cause

remedy

ERR DEFROST

Defrosting has been terminated.

Check flow rate and temperatures during defrosting.

ERR LP

Low pressure too low (< 0.1 MPa for 10 s)

The system is locked. A heat pump reset is required.

ERR MIN SUPHT

Superheating upstream of compressor too low (< 3 K for 60 s)

The system is locked. A heat pump reset is required.

ERR MAX SUPHT

Superheating too high (> 30 K for 120 s)

The system is locked. A heat pump reset is required.

ERR CIRC REFR

Evaporation temperature too low (< -30 °C at > -10 °C outside tem-

perature).

The system is locked. A heat pump reset is required.

ERR FAN

The fan in the external unit does not run.

The system will not be locked out; in the case of continuing occurrence,

notify customer service.

HP SENSOR MAX

High pressure too high (> 44.4 bar for 10 s)

The system is locked. A heat pump reset is required.

ERR HIGH PRESS

The high pressure switch has responded 5 times in 2 hours.

The system is locked. A heat pump reset is required.

ERR APP LIMIT

The maximum condensate temperature has been exceeded.

The system is locked. A heat pump reset is required.

ERR COMP

An inverter fault has occurred.

The system is locked. A heat pump reset is required.

KOMP LOCK

10 inverter faults have occurred.

The compressor starts again after the selected idle time has expired.

3 x inverter faults in 24 hours result in an error message.

INV OV CURR

The limit for maximum inverter current has been exceeded.

The compressor starts again after the selected idle time has expired.

PFC OV CURR

The limit for maximum current has been exceeded.

The compressor starts again after the selected idle time has expired.

DC OV VOLT

The limit for maximum DC voltage has been exceeded.

The compressor starts again after the selected idle time has expired.

INV DESAT

An inverter fault has occurred.

The compressor starts again after the selected idle time has expired.

INV OV TEMP

The limit for maximum inverter temperature has been exceeded.

The compressor starts again after the selected idle time has expired.

PFC OV TEMP

The limit for maximum temperature has been exceeded.

The compressor starts again after the selected idle time has expired.

LOST ROTOR

Major inverter fault: Rotor does not turn as expected.

Inverter fault, check compressor.

DC VOLT LOW

DC voltage has been fallen below the minimum limit.

The compressor starts again after the selected idle time has expired.

TORQUE LIMIT

Heat pump torque limit has been exceeded.

The compressor starts again after the selected idle time has expired.

SCR TEMP HI

The limit for maximum compressor temperature has been exceeded. The compressor starts again after the selected idle time has expired.

MOT TEMP HI

The limit for maximum compressor motor temperature has been

exceeded.

The compressor starts again after the selected idle time has expired.

«
...
57
58
59
60
61
...
»

Содержание WPL 15 IKS-2













































































Отзывы:

Нет отзывов

Похожие инструкции для WPL 15 IKS-2

Бренд: jbc Страницы: 4

Бренд: Larius Страницы: 46

Бренд: NARVI Страницы: 12

AquaMax Eco Expert 21000

Бренд: Oase Страницы: 136

Бренд: Oerlikon Barmag Страницы: 36

Бренд: Unidare Страницы: 3

Бренд: AquaPRO Страницы: 4

Omnivore XLSG200 Series

Бренд: Liberty Pumps Страницы: 12

Бренд: Cadet Страницы: 9

Бренд: ProMinent Страницы: 20

Бренд: Homa Страницы: 24

Бренд: JLF Страницы: 5

Бренд: Detroit Radiant Products Страницы: 32

Бренд: Aktobis Страницы: 5

Бренд: Comet Страницы: 12

Бренд: P.Lindberg Страницы: 54

Бренд: Pro-Elec Страницы: 2

WILDEN A1 Accu-Flo

Бренд: PSG Dover Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды