STIEBEL ELTRON WPL 15 IKS-2 Скачать руководство пользователя страница 75

Страница: 75 / 76

www.stiebel-eltron.com

WPL 15 IKS | WPL 25 IK |

INSTaLLaTION | GUaraNTEE | ENVIrONmENT aND rECYCLING

Specification

WPL 15 IKS-2

WPL 25 IK-2

Versions
Compressor oil

Emkarate RL 32 3MAF / MOBIL EAL Arctic

22 CC

Emkarate RL 32 3MAF / MOBIL EAL Arctic

22 CC

Condenser material

1.4401/Cu

Protection (IP) outdoor unit

IP14B

Protection (IP) indoor unit

IP20

Refrigerant

R410 A

Refrigerant charge

4.5

CO2 equivalent (CO2e)

10.44

12.53

Global warming potential of the refrigerant (GWP100)

2088

Dimensions
Height of the outdoor unit

920

1104

Width of the outdoor unit

1097

1271

Depth of the outdoor unit

515

Height of the indoor unit

1960

Width of the indoor unit

600

Depth of the indoor unit

650

Height when tilted

2100

Max. permissible split line length

Weights
Weight of the outdoor unit

Weight of the indoor unit

308

316

Connections
Connection, heating flow/return

28 mm

22 mm

Pipe diameter, suction gas line

16 x 1

18 x 1

Connection, liquid line

10 x 1

Water quality requirements
Water hardness

°dH

≤3

pH value (with aluminium compounds)

8.0-8.5

pH value (without aluminium compounds)

8.0-10.0

Chloride

mg/l

<30

Conductivity (softening)

μS/cm

<1000

Conductivity (desalination)

μS/cm

20-100

Oxygen 8-12 weeks after filling (softening)

mg/l

<0.02

Oxygen 8-12 weeks after filling (desalination)

mg/l

<0.1

Values
Heat loss

kW/24 h

1.9

Amount of oil

1.18

Internal volume, heating side

4.35

4.6

Pre-filled for split line length

Max. height differential, external unit higher than internal unit

Max. height differential, external unit lower than internal unit

Min. heating flow rate

m³/h

0.84

Nominal heating flow rate at A2/W35, B0/W35 and 7 K

m³/h

0.84

Heating flow rate (EN 14511) at A7/W35, B0/W35 and 5 K

m³/h

0.87

1.23

Flow rate on heat source side

m³/h

2300

4000

Permissible operating pressure, DHW

MPa

Internal pressure differential

hPa

300

160

Guarantee

The guarantee conditions of our German companies do not

apply to appliances acquired outside of Germany. In countries

where our subsidiaries sell our products a guarantee can only

be issued by those subsidiaries. Such guarantee is only grant-

ed if the subsidiary has issued its own terms of guarantee. No

other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in

countries where we have no subsidiary to sell our products.

This will not affect warranties issued by any importers.

Environment and recycling

We would ask you to help protect the environment. After use,

dispose of the various materials in accordance with national

regulations.

Guarantee

The guarantee conditions of our German companies do not

apply to appliances acquired outside of Germany. In countries

where our subsidiaries sell our products a guarantee can only

be issued by those subsidiaries. Such guarantee is only grant-

ed if the subsidiary has issued its own terms of guarantee. No

other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in

countries where we have no subsidiary to sell our products.

This will not affect warranties issued by any importers.

Environment and recycling

We would ask you to help protect the environment. After use,

dispose of the various materials in accordance with national

regulations.

GUaraNTEE

ENVIrONmENT aND rECYCLING

Содержание WPL 15 IKS-2













































































Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPL 15 IKS-2, Эксплуатация и установка

Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды