STIEBEL ELTRON WPL 15 IKS-2 Скачать руководство пользователя страница 8

Страница: 8 / 76

OPEraTION

Settings

| WPL 15 IKS | WPL 25 IK

www.stiebel-eltron.com

4.3 Adjustments at control level 1

Keeping the control flap closed, turn the rotary selector to

the operating mode you wish to adjust.

Standby mode

Frost protection is activated for heating and DHW mode.

When the flap is closed, FROST PROTECT is displayed. The

set DHW value is fixed at 10 °C, the set heating flow value

is calculated based on a set room value of 5 °C.

Application: During prolonged periods of absence, e.g.

holidays.

Automatic mode

Heating in line with the time switch program (applies

to heating circuits 1 and 2). Changeover between day

temperature and setback temperature.

DHW heating in line with the time switch program; ch-

angeover between day temperature and setback tempe-

rature. With this operating mode, an additional symbol

(sun or moon) indicates in the display, whether heating

circuit 1 is currently in day or in setback mode.

The remote control is only active in this operating mode.

Application: When DHW and central heating are required.

Constant day mode

The heating circuit (HC) is constantly held at the day tem-

perature (HC 1 and HC 2). DHW heating according to time

switch program.

Application: In low energy houses, if no setback mode

intended.

Constant setback mode

The heating circuit is constantly held at the setback tem-

perature (HC 1 and HC 2). DHW heating according to time

switch program.

Application: During weekends away.

DHW mode

DHW heating in line with the time switch program; ch-

angeover between day temperature and setback tem-

perature. Frost protection is enabled for heating mode.

Application: The heating season has ended; only DHW

should be generated (summer mode).

Electric emergency/booster heater

This setting activates the electric emergency/booster

heater. In this operating mode, the electric emergency/

booster heater provides DHW and room heating, irres-

pective of the dual mode changeover point.

Fault message (flashing)

This symbol indicates faults in the heat pump system.

Inform your contractor immediately.

Silent mode

Reduced noise mode

Silent mode is enabled. The associated time programs

determine activation of the fan or compressor throttle.

Note

Silent mode has an effect on the heating output

and efficiency of the heat pump.

When silent mode 2 is active, higher electricity

bills result.

Silent mode 1

The fan and / or compressor run with reduced output.

Silent mode 2

Compressor and fan are stopped. Heat generator 2 takes

over heating.

4.4 Overview of control level 2

Control level 2 is accessed as follows:

Open the control flap.

Select the required parameter with the rotary selector. Turn

the rotary selector until the arrow is visible above the menu

item you require.

The selected menu item is displayed as plain text. The arrow in-

dicates the menu position within the control level.
You can now adjust the values for the following menu items (see

following chapters).

ROOM TEMP HC 1

Here you can select the set room temperature for day and setback

mode for heating circuit 1.

ROOM TEMP HC 2

Here you can select the set room temperature for day and setback

mode for heating circuit 2. Room T HC2 will only be displayed if

the mixer flow sensor for heating circuit 2 has been connected.

Note

The actual room temperature can also be scanned here,

provided the FE 7 remote control has been connected and

allocated to HC 1 or HC 2.

DHW TEMP

Here you can assign a set day and night value for the temperature

in the DHW cylinder.

TIME / DATE

Here you can adjust the time and summer time. At the factory,

summer time is set to begin on 25 March and to end on 25 October.

HOLIDAY/PARTY

You can indicate the length of your holiday using the HOLIDAY

menu item (start date, end date). The heat pump system will ope-

rate in setback mode for the selected period. Frost protection for

the DHW cylinder is active.

Содержание WPL 15 IKS-2













































































Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPL 15 IKS-2, Эксплуатация и установка

Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды