STIEBEL ELTRON WPL 15 IKS-2 Скачать руководство пользователя страница 43

Страница: 43 / 76

INSTaLLaTION

Commissioning

www.stiebel-eltron.com

WPL 15 IKS | WPL 25 IK |

Fully open the heating circuit(s) in the lead room.

Close all other heating circuits.

If an overflow valve has been installed in the heating system,

fully close this overflow valve in order to determine the mini-

mum flow rate.

In menu „START UP / HEATING“, set the parameter „SET HTG

P RATE“ (heating circuit pump rate) so that the minimum

flow rate required for system operation is assured (see chap-

ter „Specification“).

The current flow rate can be called up in menu „INFO / TEMPE-

RATURES“ under „ACT VOLUME“.

Note

Never change parameter "SET DHW P RATE" in menu

"START UP".

The pump speed for DHW operation was optimised at the factory.

12.3.2 Minimum flow rate for systems with a buffer cylinder

For systems with a buffer cylinder: in menu „START UP“, set pa-

rameter „B-PUMP CONST“ to „OFF“.

In menu „START UP“, set parameter „SET HTG P RATE“ so

that the nominal flow rate required for system operation is

assured (see chapter „Specification / Data table“).

The current flow rate can be called up in menu „TEMPERATURES“

under „ACT VOLUME“.

Note

Never change parameter "SET DHW P RATE" in menu

"START UP".

The pump speed for DHW operation was optimised at the factory.

12.4 Operation and control

Material damage

Never interrupt the power supply, even outside the he-

ating period. The system's active frost protection is not

guaranteed if the power supply is interrupted.

There is no need to switch the system off in summer. The heat

pump manager has an automatic summer / winter changeover.

12.5 Decommissioning

If the system is to be taken out of use, set the heat pump manager

to standby. This retains the safety functions designed to protect

the system (e.g. frost protection).

Содержание WPL 15 IKS-2













































































Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPL 15 IKS-2, Эксплуатация и установка

Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды