STIEBEL ELTRON WPL 15 IKS-2 Скачать руководство пользователя страница 52

Страница: 52 / 76

INSTaLLaTION

Commissioning

| WPL 15 IKS | WPL 25 IK

www.stiebel-eltron.com

After that, the heat pump and the associated buffer primary pump

are switched on.

Press the programming key again or close the control flap to

exit the parameter.

OFF is displayed.

RELAY TEST

From here the following relay outputs of the heat pump manager

can be individually controlled:

- BUFFER

- DHW VALVE

- DRAIN HYD (this is the centre position of the DHW valve)

- HTG CIRC PUMP

- MIXER PUMP

- MIXER OPEN

- MIXER CLOSED

- DHC 1

- DHC 2

- HP ON

Press the programming key and turn the rotary selector.

The individual outputs are displayed as plain text.

LCD TEST

Here you can initiate a test of the LCD display.

Press the programming key once to initiate the LCD test.

All display elements are displayed in sequence.

FAULT LIST

This displays any fault codes that may arise.

Press the programming key to show the first fault code.

The fault is shown at the top of the display as plain text; the fault

number appears at the bottom of the display.

Turn the rotary selector to display additional information.

The first fault continues to be displayed. The day, month, year and

time when the fault occurred are displayed by way of additional

information.
In total, 20 faults can be displayed.

You can delete the fault list by carrying out a hardware reset.

Example:
A HP FAULT occurred on the 17/07/2012 at 14:50 h representing

the latest fault in the heat pump.

�0

3�

�1

ERR T FROST

WPMME SOFTWARE

Display of the current software issue.

MFG SOFTWARE

Display of the current software issue.

ANALYSIS

The enabled stages are shown on the display.
The two-digit display shows the internal control unit calculation.

A stage is switched each time the counter goes down to zero.

This calculation depends on the control dynamic and the control

deviation. For this, see CNTRL RESP TM.

DIAGNOSIS

This checks whether an FEK control unit is connected.

Press the programming key.

MAN DEFROST

Manual defrost can only be initiated when the heat pump is in

operation.
The flow temperature at the condenser is monitored during de-

frosting. If the flow temperature falls below 15 °C, the electric

emergency/booster heater is started, independent of the dual

mode point, to provide additional heating.
However, if during defrosting the flow temperature falls to 10 °C,

the heat pump is switched off and the electric emergency/booster

heater regulates to the set heating circuit temperature.
The DEFROSTING fault is displayed.

HEAT P RESET

Here you can reset the heat pump in the event of a fault.

Press the programming key.

Go to the setting ON.

Press the programming key repeatedly.

The fault is reset. The heat pump restarts once a blocking time of

2 minutes has elapsed. The fault remains stored in the fault list.

RUNTIME

Pressing the programming key will successively call up the run-

times of the compressor and electric emergency/booster heater

in hours. These runtimes can only be reset via a hardware reset.

INfO WPmme

RNT COMP HTG

Runtime - compressor in heating mode

RNT COMP DHW

Runtime - compressor in DHW mode

RUNTIME DHC 1

Runtime DHC 1 in heating mode and DHW mode

RUNTIME DHC 2

Runtime DHC 2 in heating mode and DHW mode

COMP STARTS

Compressor starts

Содержание WPL 15 IKS-2













































































Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPL 15 IKS-2, Эксплуатация и установка

Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды