STIEBEL ELTRON WPL 15 IKS-2 Скачать руководство пользователя страница 37

Страница: 37 / 76

INSTaLLaTION

Power supply

www.stiebel-eltron.com

WPL 15 IKS | WPL 25 IK |

11.3 Electrical connection of external unit

Material damage

The electrical cables for the control voltage and the

power supply for the fan must be laid separately from

each other.

11.3.1 Access to the connecting chamber

�0

3�

�1

Undo the screws and remove the cover.

�0

3�

�1

Undo the screw and open the cover.

�0

3�

�18

1 Entry electrical cables

Push the electrical installation cables from below through

the „Entry electrical cables“. As the cables are being pushed

through, a cable guide inside the appliance directs the cables

upwards towards the connection area.

Connect cables according to the following diagram.

�0

3�

�1

mains (control voltage from internal unit)

L, N, PE

X2 fan (power supply from internal unit)

L, N, PE

X3 BUS cable from internal unit

BUS G

BUS –

BUS +

X4 ribbon heater

L, N, PE

Route cables and leads through the strain reliefs.

Check the function of the strain relief fittings.

Close the appliance.

Содержание WPL 15 IKS-2













































































Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды

STIEBEL ELTRON WPL 15 IKS-2, Эксплуатация и установка

Результаты поиска

Содержание WPL 15 IKS-2

Отзывы:

Похожие инструкции для WPL 15 IKS-2

Бренды по названию

Популярные бренды