QB Expert Alpha Controller
114
Special Application Tools
Arming
Normal
Operation
Operator Does Not Press
MFB to Arm Tool
Tool is Disabled
Not
Required
Assembly Mode:
After the operator starts the tool
and when the trigger switch is
released the tool switches to
Homing mode. Tool does not
have to reach target.
Assembly Mode:
Tool will run in Normal
Assembly mode when
operator presses the start
trigger switch.
When operator releases start
trigger switch the tool will
switch to Homing mode.
Assembly Mode:
The tool will not run when
operator pulls the trigger. The
controller display will indicate
“Error Proofing”.
When operator releases start
trigger switch the tool will
switch to Homing mode.
Homing Mode:
Tool will run in Homing mode
when operator presses the start
trigger switch.
Tool will remain in Homing
mode until one of the following
conditions is met:
1. Dog Torque is achieved.
2. Total Homing angle is <360°
when operator releases the
start trigger switch.
3. ARM Timeout has elapsed.
Homing Mode:
Tool will run in Normal
Homing mode when operator
presses the start trigger
switch.
Homing Mode:
Tool will run in Normal Homing
mode when operator presses
the start trigger switch.
Required
Assembly Mode:
Operator must ARM the tool by
pressing the MFB once quickly.
Operator must start the tool
before ARM times out. When the
start trigger switch is released
the tool switches to Homing
mode. Tool does not have to
reach target.
Assembly Mode:
The tool will not run. The
controller display will indicate
“Arming Required”.
Assembly Mode:
The tool will not run when
operator presses the start
trigger switch. The controller
display will indicate “Error
Proofing”.
When operator releases start
trigger switch the tool will
switch to Homing mode.
Homing Mode:
Tool will remain in Homing
mode until one of the following
conditions is met:
1. Dog Torque is achieved.
2. Total Homing angle is <360°
when operator releases the
start trigger switch.
3. ARM Timeout has elapsed.
Homing Mode:
The tool cannot enter Homing
mode unless the tool has
been armed in the assembly
mode at least once.
Homing Mode:
Tool will run in Normal Homing
mode when operator presses
the start trigger switch.
Содержание QB Expert
