Sperry Marine Visionmaster FT ECDIS Скачать руководство пользователя страница 329

Страница: 329 / 531

ECDIS User Guide

Alerts

65900012

7-31

Alert Type

Description

Priority

Notes

Standby/Transmit

Error

The standby transmit state of the transceiver is in conflict

Warning

Steering Control

Received

The autopilot has transferred steering control to this system.

Control of the heading command and the ability to activate track

control is available at one or more stations.

Warning

Steering Control

Relinquished

System has relinquished steering control. Autopilot or another

device or system will control steering until control is transferred

back to this system.

Warning

Stern Ground Speed

Unusable

Sensor Stern Ground Speed Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

STPW Unusable

Sensor Ship Total Power Integrity VisionMaster FT

applicable when Track Control is configured and for ECDIS only

configurations.

Alarm or

Caution

Depending on

configuration

STW Unusable

Sensor Speed Through Water Integrity VisionMaster FT

Alarm,

Warning or

Caution

Depending on

configuration

System Tracks Almost

Full

Tracking 95% of the system maximum number of targets

Caution

System Tracks Full

Tracking the system maximum number of targets.

Warning

Target Anchor Drift

Target out of the anchor watch limit circle.

Warning

Targets Full

System cannot allocate any more target numbers

Warning

Temperature

Unusable

Sensor Temperature Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Temporary

Authorization

System is only temporarily authorized

Warning

Содержание Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Visionmaster FT ECDIS

Отзывы:

Похожие инструкции для Visionmaster FT ECDIS

Бренды по названию

Популярные бренды

Sperry Marine Visionmaster FT ECDIS, Руководство пользователя

Результаты поиска

Содержание Visionmaster FT ECDIS

Отзывы:

Похожие инструкции для Visionmaster FT ECDIS

Бренды по названию

Популярные бренды