Sperry Marine Visionmaster FT ECDIS Скачать руководство пользователя страница 322

Страница: 322 / 531

Alerts

ECDIS User Guide

7-24

65900012

Alert Type

Description

Priority

Notes

I/O Device

Unavailable

I/O Device Unavailable

Warning

Inaccurate Chart

Positions on this chart are inaccurate, because this chart does not

provide a mapping to standard WGS-84 coordinates.

Warning

Incompatible PCIO

firmware

PCIO firmware required is v1.04 or later.

Warning

Incorrect Compass

Ratio.

Configured compass ratio is incorrect for current board type.

Warning

Internal Error

An unrecoverable internal error has occurred, please restart the

equipment

Warning

Interswitch Comms

Interswitch communications failed. Transceiver source unknown.

Top Unit settings may be invalid (e.g. Heading Marker Offset,

Turning Unit Offset)

Warning

Interswitch Model

Conflict

The interswitch model conflicts with the configured model

Warning

Interswitch Request

Failed

The Interswitch request failed.

Warning

Invalid Datum In Use

Datum in use is not WGS84.

Warning or

Caution

Depending on

configuration

Invalid Network

Config

Invalid network configuration detected.

Warning

IO Comms Interrupted

IO communications interrupted on an Alert Management Interface. Caution

IO Comms Reception

IO communications unavailable for Alert Management Interface.

Caution

Local Time Offset

Unusable

Sensor Local Time Offset Integrity VisionMaster FT

Alarm or

Caution

Depending on

configuration

Содержание Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Visionmaster FT ECDIS

Отзывы:

Похожие инструкции для Visionmaster FT ECDIS

Бренды по названию

Популярные бренды

Sperry Marine Visionmaster FT ECDIS, Руководство пользователя

Результаты поиска

Содержание Visionmaster FT ECDIS

Отзывы:

Похожие инструкции для Visionmaster FT ECDIS

Бренды по названию

Популярные бренды