Sperry Marine Visionmaster FT ECDIS Скачать руководство пользователя страница 324

Страница: 324 / 531

Alerts

ECDIS User Guide

7-26

65900012

Alert Type

Description

Priority

Notes

Maximum Latitude

Exceeded

Due to maximum latitude being exceeded, system inaccuracies may

develop and functionality may be disabled. Inaccuracies generally

become more serious as own ship travels toward the pole after

exceeding the maximum latitude. Do not rely on system as primary

means of navigation when operating beyond the maximum

latitude.

Caution

Minimal Safety Region

A low value for look-ahead time or distance has resulted in a small

safety region for detecting chart dangers on own ship's course.

This may not provide adequate time to take action if a danger is

detected. Use the 'Chart Dangers' menu to increase look-ahead if

necessary.

Caution

Monitor Comms

No Response: The system is unable to communicate with the LCD

through its serial port. Use the external knob to manually adjust

backlight brightness.

Warning

Monitor Data

Bad Data: The LCD monitor failed to acknowledge a command.

Use the external knob to manually adjust backlight brightness.

Warning

Multiple Interfaces On

SCU

A switched SCU is communicating over multiple interfaces.

Warning

Multiple Master SCUs

The autopilot has identified multiple master SCUs.

Warning

Next Turn EBL Comms

No messages received from external VMS system.

Warning

No CAM Watchmode

There are no CAM supporting product types in the system in CAM

watch mode.

Caution

No Set and Drift for

MOB

Man Over Board is active with no valid set and drift data. MOB

event marker position is the drop location and will not be adjusted

for set and drift.

Warning

Содержание Visionmaster FT ECDIS




















































































































































































































































































































































































































































































































































Результаты поиска

Содержание Visionmaster FT ECDIS

Отзывы:

Похожие инструкции для Visionmaster FT ECDIS

Бренды по названию

Популярные бренды

Sperry Marine Visionmaster FT ECDIS, Руководство пользователя

Результаты поиска

Содержание Visionmaster FT ECDIS

Отзывы:

Похожие инструкции для Visionmaster FT ECDIS

Бренды по названию

Популярные бренды