background image

Service record Dynamis MV

31 von 36

2021-01-12

5  Technical data

Model: Dynamis MV 

Model: Dynamis MV 

Type: 793 

Type: 793 

Dimensions

Dimensions ± 5%

Description

Measurements

Comment

seat width (SW)

Ergo-seat

320 - 500 mm | in 20 mm steps

growing by  40 mm

seat depth (SD)

Ergo-seat

340 - 520 mm | in 20 mm steps

growing by  20 mm

back height (BH)

Underframe

430 or 500 mm

Ergo-seat

400-650 mm | in 50 mm steps

back unit:

adjustable in depth by + 40 / -20 

mm

back angle

default setting 90° / 95° / 100°

dynamic

from the preset angle up to 120 °

lower leg length

220-450 mm

Upper edge of seat plate to foot plate

ETRTO wheel size

at 20''

Ø 451 mm

ETRTO wheel size

at 22''

Ø 489 mm

ETRTO wheel size

at 24''

Ø 540 mm

Handrim diameter 

at 20''

Ø 444 mm

at 22''

Ø 481 mm

at 24''

Ø 533 mm

handrim

Ø 19 mm

Pipe diameter

camber

0°, 2°, 5°, 8°, 11° 

seat height (SH) front

min.

380 mm

The seat heights are measured from the top 

edge of the seat to the floor, WITHOUT the 

seat cushion.

seat height (SH) front

max.

520 mm

seat height (SH) back

min.

325 mm

seat height (SH) back

max.

585 mm

overall width

min.

SB + 200 mm

max.

SB + 405 mm

overall length

min.

875 mm

max.

1135 mm

without outdoor front end

Total height (including push 

handle in 45 ° position)

min.

1045 mm

max.

1320 mm

Capacity 

max.

90 kg

Permissible incline

12,3% = 7°

at 0 ° inclination of the back angle

Permissible slope

12,3% = 7°

steadiness

12,3% = 7°

Turning circle

about 1050 mm

depending on the wheelchair size

Individual weights

drive wheels

0,97 - 2 kg

depending on the design and size

tires

Commercially available pneumatic tires sizes 1 ", 1 3/8" or puncture-proof tires (same dimensions), 

tire pressure usually 3-10 bar.

Corrosion protection

Material

Stainless steel, aluminum

Coating

Powder coating, galvanizing

Service life

3 years

if the wheelchair is not used excessively

lifespan

5 years

normative requirements

The wheelchair meets the requirements of ISO 7176-8 and the requirements against ignition

Minimum empty weight.

Roadworthy 

with RB 300 

mm, 20 '' rear 

wheels, 5 '' PU 

caster wheels

20,35 kg

Frame size 1, seat frame, 22 '' wheels with 

drum brakes, PU caster wheels, legrests, push 

bow

5.1  Data and dimensions

Содержание Dynamis MV





































Отзывы: