Sony D8 Digital Handycam DCR-TRV420E, Руководство по обслуживанию

Страница: 187 / 287

5-50
5. APC & AEQ Adjustment (VC-235 board)
Mode Camera record and playback
Subject Arbitrary
Measurement Point Pin qh of CN1108 (RF MON)
(Note 1)
External trigger : Pin
qd
of CN1108
(DV RF SWP)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 18, 19, 1B, 1C, 21, 2C
Specified Value The display data of page: 3, address:
03 is “00”
Note 1:
Connect a 75
Ω
resistor between Pin
qh
and Pin
6
(GND)
of CN1108.
75
Ω
resistor (Parts code: 1-247-804-11)
Note 2: Use a Hi8 MP tape.
Adjusting method:
1)
Select page: 0, address: 01, and set data: 01.
2) Select page: 8, address: 2A, set data: C8, and press the PAUSE
button of the adjustment remote commander.
3) Record the camera signal for a minute.
4) Select page: 2, address: 2E, and set data: 01.
5) Playback the recorded segment.
6) Select page: 3, address: 33, and set data: 08.
7) Confirm that the playback RF signal is stable.
8) Select page: 3, address: 01, set data: 07, and press the PAUSE
button.
9) Select page: 3, address: 02, and check that the data changes
from “07” to “00” in about 20 seconds after pressing the PAUSE
button.
10) Select page: 3, address: 03, and check that the data is “00”.
Note 3:
If the data of page: 3, address: 03 is other than “00”,
adjustment has errors.
11) Select page: 3, address: 33, and set data: 00.
12) Select page: 2, address: 2E, and set data: 00.
13) Select page: 8, address: 2A, set data: 00, and press the PAUSE
button.
14) Select page: 0, address: 01, and set data: 00.
Fig. 5-3-6
6. PLL f
0
& LPF f
0
Final Adjustment (VC-235 board)
Mode VTR stop
Signal Arbitrary
Measurement Point Display data of page: 3, address: 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 1F, 20, 22, 29
Specified Value Bit values of bit2, bit3 and bit6 are “0”
Adjusting method:
1)
Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 01, set data: 30, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 3, address: 02, and check that the data changes to
“00”.
4) Select page: 3, address: 03, and check that bit values of bit2,
bit3 and bit6 are “0”.
Note:
If bit value of bit 2, bit 3 or bit 6 is “1”, there are errors.
For the error contents, see the following table. (For the
bit values, refer to “5-4. SERVICE MODE”, “4-3. 3.
Bit value discrimination”)
Bit value of page: 3,
Error contents
address: 03
bit 6 = 1 LPF f
0
adjustment is defective
bit 3 = 1 PLL f
0
, fine adjustment is defective
bit 2 = 1 PLL f
0
, fine adjustment is defective
5) Select page: 0, address: 01, and set data: 00.
13.3 msec
PB RF signal is stable
Pin
qd
Pin
qh