Sonardyne UM-8300-Compatt 6, Руководство пользователя

Страница: 8 / 141

Figure 3–4 Mini Compatt 6 7
Figure 3–5 Maxi Compatt 6 7
Figure 3–6 Dynamic Positioning Transponder 6 Transponder 8
Figure 3–7 Pressure Inverted Echo Sounder Transponder 8
Figure 3–8 Autonomous Monitoring Transponder 9
Figure 3–9 Sensor Logging Transponder 10
Figure 3–10 Transducer Endcap Internal Connectors 12
Figure 3–11 Example of a Sensor Endcap 13
Figure 3–12 Subconn MCBH8F Connector 14
Figure 3–13 Battery Disconnect Fob 15
Figure 4–1 Example of Inclinometer Mounting Kit 19
Figure 4–2 Example of Stab Mounting Kit 20
Figure 4–3 Recommended Specification for Inclinometer Endcap Mounting Plate 21
Figure 5–1 Rolling the Transponder off the Deck 22
Figure 5–2 Lowered by Vessel Crane or A-Frame – Single Transponder Installation 23
Figure 5–3 Lowered by Vessel Crane or A-Frame – Multiple Transponder Installation 23
Figure 5–4 Acoustic Release used as a Crane Hook 24
Figure 5–5 Slip Hook with Integral Swivel 25
Figure 5–6 ROV grabs one metre loop of Rope 25
Figure 6–1 Responder Input 26
Figure 8–1 Fitting the Bulkhead Plate 38
Figure 8–2 Inspecting the Transducer Endcap 38
Figure 8–3 Removing the Protective Guard 39
Figure 8–4 Removing the Guard and Bump Stop 40
Figure 8–5 Removing Transducer Housing using the Opening Tools (Omni-Directional shown for
Reference)
40
Figure 8–6 Cleaning the O-ring Seals (Omni-Directional shown for Reference) 41
Figure 8–7 Refitting the Guard and Bump Stop 42
Figure 8–8 Securing the Bump Stop and Guard 43
Figure 8–9 Removing the Clamp Rings 44
Figure 8–10 Removing the Rubber Bump Stop 44
Figure 8–11 Removing Transducer Housing using the Opening Tools 45
Figure 8–12 Cleaning the O-ring Seals 45
Figure 8–13 Fitting Clamp Rings and Bumper Stop 47
Figure 8–14 Securing Bump Stop to Clamp Rings 47
Figure 8–15 Figure 0-13 Remove the Sensor Endcap 48
Figure 8–16 Removing the Sensor Endcap 49
Figure 8–17 Sensor Endcap and Chassis 49
Figure 8–18 Disconnecting PL1 Connection from the Interface PCB Assembly 50
Figure 8–19 Disconnecting PL2 Connection from the Interface PCB Assembly 50
Figure 8–20 Disconnecting the Ribbon Cable from the Interface PCB Assembly 51
Figure 8–21 Disconnecting the Sensor Endcap from the Main Chassis 51
Figure 8–22 Abutting Chassis and Sensor Endcap 53
Figure 8–23 Securing the Sensor Endcap to the Chassis 53
Figure 8–24 Interface PCB Connections 54
Figure 8–25 Inserting the Chassis into the Housing 54
Figure 8–26 Fitting the Bulkhead Plate over the Pins 57
Figure 9–1 Compatt 6 Connected to the PC using the Dual Serial Cable 60
Figure 9–2 Dual Serial Cable 61
User Manual for the Type 8300 Compatt 6
(and Variants)
UM-8300-Compatt 6
Issue B3
vii