background image

Safety

Safety

A1 Hybrid series

 

inverter is designed and certified to meet stringent Ul1741/

IEEE 1547 and ANSI/IEEE 62.41/62.42 lighting and surge requirements.
However, every PV installation is unique. Thus, additional external UL/NEC AC and 
DC surge protection and solid grounding practices are recommended.

Battery Safety Instructions

A1 Hybrid Series inverter should be coupled with a high voltage battery.
The battery must comply with UL 1973 and must be intrinsically safe. 
For the specific parameters such as battery type, nominal voltage and nominal 
capacity etc., refer to Section 

4.3.

As accumulator batteries may contain potential electric shock and short-circuit 
current dangers, to avoid accidents that might be thus resulted, the following 
warnings should be observed during battery replacement:

   1: Do not wear watches, rings or similar metallic items.
   2: Use insulated tools.
   3: Put on rubber shoes and gloves.
   4: Do not place metallic tools and similar metallic parts on the batteries.
   5: Switch off loads connected to the batteries before dismantling battery 
       connection terminals.
   6: Only personnel with proper expertise should carry out the maintenance of  
       accumulator batteries.

2.2  Explanation of Symbols 

This section gives an explanation of all the symbols shown on the inverter and on 
the type label.

CAUTION! Risk of electric shock from energy stored in the capacitor. Never 
operate on the inverter couplers, the Mains cables, battery cables, PV cables when 
power is applied. After switching off the PV, battery and Mains, always wait for 5 
minutes to let the intermediate circuit capacitors discharge before unplugging 
DC, battery plug and Msins couplers.

When accessing the internal circuit of the inverter, it is very important to wait 5 
minutes before operating the power circuit or demounting the electrolyte 
capacitors inside the device. Do not open the device beforehand since the 
capacitors require time to sufficiently discharge!

Measure the voltage between terminals UDC+ and UDC- with a multi-meter 
(impedance at least 1Mohm) to ensure that the device is discharged before 
beginning work (35VDC) inside the device.

Lightning and surge protection

Symbols on the Inverter

Symbol

Explanation

Operating Display.

An error has occurred, inform your installer immediately.

Symbols on the Type Label

Symbol

Explanation

Type1

 

Arc-Fault Circuit-interrupter in PV side.

Beware of hot surface.

The inverter can become hot during operation. Avoid contact 

during operation.

Danger of high voltages.
Danger to life due to high voltages in the inverter!

Danger.
Risk of electric shock!

Observe enclosed documentation.

Do not operate this inverter until it is isolated from the battery,  grid 
and the PV.

CSA certified.

  PV
AFCI

Type 1

Battery Status.

Danger to life due to high voltage.

There is residual voltage existing in the inverter after powering off 

which needs 5 minutes to discharge.

Wait 5 minutes before opening the upper lid or the DC lid.

Warning!
When a ground fault is indicated, normally grounded conductors 
may be ungrounded and energized or normally ungrounded 
conductors may be grounded.

272687

05

04

Содержание A1-Hybrid Series












































Отзывы: