background image

Firmware Upgrading

Inverter Manipulation

 

 NOTE!

   

If the left indicator do no turn green please check the below points:

    - All the connections are correct.
    - All the external breakers are switched on.
    - The DC switch on the inverter is in the “ON” position.

Step 1.

 

Switch the manual bypass breaker to connect with grid side.

Step 2

.  

Turn off the Grid breaker and the battery breaker.

Step 3

.  

Turn off the DC switch at the bottom of the inverter to the “OFF” position.

Step 4

.  

Turn off the main switch if needed.

8.2 Start  Inverter

Step 2. Turn on the DC switch at the bottom of the inverter.

Step 5. Select the wanted voltage through the screen, such as 240V.

Step 6. Then choose the grid standard, IEEE1547 or RULE21.

Step 7.

 

The inverter will start up and ISO, IMI, Relay will start self-checking 

automatically  when the PV panels generate enough power or the battery is 
discharging.

Step 8. Check the status of indicators and LCD screen. The left indicator should 
           be green and the indicator screen should display the main interface.

Step 9.

 

Set Wi-Fi / LAN according to Wi-Fi / LAN user manual. (if needed)

Step 10. Create a monitor web account according to the Wi-Fi / LAN user manual. 

8.3 Shutdown  Inverter

Step 1. Adjust the DIP Switch according to the number of battery segments.

Step 4. Press the button and turn on the circuit breaker.

Step 3. Turn on the AC switch.

9  Firmware Upgrading

The inverter firmware can be upgraded via a U-disk.

Ensure the inverter is powered on.
The inverter must be connected to the PV panels and the battery must be 
operating while the  rmware upgrade is in progress.
Please prepare a PC and an U-disk.

9.1 Preparation

WARNING!

Make sure the PV input power is more than 150V (operate the 
upgrade on a sunny day), otherwise it may result in serious failure 
during upgrading.

Step 1. Contact our service support to get the update  les, and extract it into your 
U-disk as follow:

“update\ARM\xxx.xxxxx.xx_Hybrid_A1_Manager_Vx.xx_xxxx.usb”,
“update\DSP_Master\xxx.xxxxx.xx_Hybrid_A1_Master_Vx.xx_xxxx.hex”,
“update\DSP_Slave\xxx.xxxxx.xx_Hybrid_A1_Slave_Vx.xx_xxxx.hex”,
“update\BMS_Slave\xxx.xxxxx._SolaxBat_Sxx_xxxx_Vx.xx_xxxx.hex”;
“update\BMS_Master\xxx.xxxxx._SolaxBat_M_xxxx_Vx.xx_xxxx.hex”.
(xxx.xxxxx.xx is the P/N, Vx.xx is version number, xxxx is  le complation date)

9.2 Upgrading Steps

Software version can be found in the “About”  display. 
The way to check software version from the “About” screen:
1) Access the “About” display by pressing “OK”  button when the LCD shows the
main display.

Refer to the flow diagram below:

 Status
 History
 Setting
 System Switch
>About

 Menu

About

About

>Inverter DSP1:
                      XX

>Inverter DSP2:
          XX

48

49

Содержание A1-Hybrid Series












































Отзывы: