Smiths Graseby MS16A Скачать руководство пользователя страница 9

Страница: 9 / 61

M S 1 6 A S y r i n g e D r i v e r

Te c h n i c a l S e r v i c e M a n u a l

I s s u e 6 ( F e b r u a r y 2 0 0 5 )

P a g e v i i

S m i t h s M e d i c a l

Warnings

Warnings tell you about dangerous conditions that may occur, and

which could lead to death or serious injury to the user or patient if

you do not obey all of the instructions in this manual.

Remember the rate is set in milliMETRES

NOT milliLITRES. The correct rate is essential to

prevent serious injury or death to the patient.

Any damaged pumps must be thoroughly tested by a competent person in accordance with the

procedures in this service manual before re-use with a patient. Failure to observe this may result

in patient injury or death.

Completely prime the administration set, and remove all air from both the administration set and

the syringe before measuring the mm of fluid length, otherwise the rate calculation will be

incorrect.

The driver must only be used with the syringe rubber securing strap fixed firmly in place, thus

preventing an uncontrolled infusion to the patient that could result in serious injury or death.

Never take a syringe that is not empty off the driver if it is still connected to the patient.

The infusion line must first be clamped or disconnected to prevent serious injury or death to the

patient.

The use of spare parts other than those recommended is not advised, and may affect the correct

operation of the driver, resulting in injury or death.

The syringe driver must not be used for infusing medication where pulsatile delivery action is

unacceptable.

The syringe driver must not be used in environments with flammable gas mixtures or with oxygen-

enriched atmospheres.

If the syringe driver is used in the lockbox, the alarm volume will be reduced.

SM0105-CON-6.PMD

2/23/2005, 12:12 PM

Содержание Graseby MS16A






























































Результаты поиска

Содержание Graseby MS16A

Отзывы:

Похожие инструкции для Graseby MS16A

Бренды по названию

Популярные бренды

Smiths Graseby MS16A, Техническое и сервисное руководство

Результаты поиска

Содержание Graseby MS16A

Отзывы:

Похожие инструкции для Graseby MS16A

Бренды по названию

Популярные бренды