Smiths Graseby MS16A Скачать руководство пользователя страница 47

Страница: 47 / 61

Te c h n i c a l S e r v i c e M a n u a l

I s s u e 6 ( February 2 0 0 5 )

5 — 9

S m i t h s M e d i c a l

M S 1 6 A S y r i n g e D r i v e r

Timer and feed rate tests

Place the syringe driver in the Linear Accuracy Rig,

part number

0105-0858

, place the dti extension rod on the actuator assembly and

set the dti to zero.

With a supply of 9 volts, set the rate to 55 and check that the

time for 5 motor pulses to occur is 36 - 41 secs. Ensure that the

actuator advances along the leadscrew a distance of 0.55 - 0.61 mm

in this time.

Set the rate to 66 and check that the time for 5 motor pulses to

occur is 30 - 33.5 secs.

Set the rate to 99 and check that the time for 10 motor pulses to

occur is 40 - 45 secs.

Hold down the

START/TEST

pushbutton

and check that the motor starts and then stops and sounder

cuts in between 3.3 - 4.0 secs.

d. Release the

START/TEST

pushbutton. Observe that the unit

restarts, with flashing LED and a single motor pulse.

Cam alignment

Increase power supply to 10 V DC and check that six pulses equals

one revolution of the leadscrew.

Half nut slip

Set the supply at 10 V DC and rate at 99. Check for correct stalling.

The LED must stop flashing, the alarm must sound, and the half nut

must

not

slip, when the actuator runs to the end of the leadscrew.

Repeat at least twice.

Rate switch test

Set rate to 36 and check that the time for 10 motor pulses to

occur is 11 - 13 secs.

Set rate to 00 and start the driver (LED flashing). Check that no

motor pulses occur over a period of at least 8 minutes. This can

be most easily determined by an absence of actuator movement.

The syringe driver may be removed from the Linear Accuracy Rig

before continuing.

10. Current tests

At a supply voltage of 9 V DC, measure the supply current with

the unit in the OFF state (LED not flashing, alarm silent). Check

this does not exceed 5 mA.

Set rate to 00 and start unit (LED flashing). Check that the

supply current (excluding LED flashes) does not exceed 50 mA at

any time in a 30 second test period.

SM0105-5-6.PMD

2/23/2005, 3:07 PM

Содержание Graseby MS16A






























































Результаты поиска

Содержание Graseby MS16A

Отзывы:

Похожие инструкции для Graseby MS16A

Бренды по названию

Популярные бренды

Smiths Graseby MS16A, Техническое и сервисное руководство

Результаты поиска

Содержание Graseby MS16A

Отзывы:

Похожие инструкции для Graseby MS16A

Бренды по названию

Популярные бренды