Smiths Graseby MS16A Скачать руководство пользователя страница 10

Страница: 10 / 61

M S 1 6 A S y r i n g e D r i v e r

P a g e v i i i

I s s u e 6 ( F e b r u a r y 2 0 0 5 )

Te c h n i c a l S e r v i c e M a n u a l

S m i t h s M e d i c a l

Cautions

Cautions tell you about dangerous conditions that can occur which

may cause damage to the pump if you do not obey all of the

instructions in this manual.

A damaged pump must never be put into active service, as it

may be a hazard to patients through under- or over-infusing.

To prevent serious damage to the driver it must

not be immersed in any liquids or exposed to

strong organic solvents. If immersion occurs or the driver is subject to a serious spillage or

wetting incident, it must be thoroughly tested by a competent person in accordance with the

procedures in this service manual before re-use with a patient.

Wipe off spills immediately. Do not allow fluid or residues to remain on the pump.

The pump is not designed to be autoclaved, steam-sterilised, ETO sterilised or subjected to

temperatures in excess of 45° C (113° F). Failure to observe this caution may cause serious damage

to the pump.

4. To avoid possible malfunction of the pump, do not expose the pump to X- rays, gamma rays or

other ionizing radiation, or to the RF interference or strong electric / magnetic fields emitted (for

example) by arc welding equipment or mobile transmitting equipment.

Moving parts of the driver do not require lubrication during their lifetime. Worn or stiff parts

should be replaced.

Handling the printed circuit board is required during disassembly/ assembly. A static controlled

work station including a conductive mat and grounded wrist strap should be used to provide

protection against electrostatic discharge (ESD) or circuit board damage could result.

Take care to avoid contamination of the exposed switches, circuit tracks and components, e.g. by

the entry of solder particles.

Refer all service, repair, testing and calibrations to suitably qualified technical personnel.

Unauthorised modifications to the driver must not be carried out.

Federal law restricts these Syringe Drivers for use by or on the order of a physician. This applies to
drivers distributed

only within the United States.

SM0105-CON-6.PMD

2/23/2005, 12:12 PM

Содержание Graseby MS16A






























































Результаты поиска

Содержание Graseby MS16A

Отзывы:

Похожие инструкции для Graseby MS16A

Бренды по названию

Популярные бренды

Smiths Graseby MS16A, Техническое и сервисное руководство

Результаты поиска

Содержание Graseby MS16A

Отзывы:

Похожие инструкции для Graseby MS16A

Бренды по названию

Популярные бренды