Smartgen HGM 9310CAN Series Скачать руководство пользователя страница 63

Страница: 63 / 77

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER

HGM93XX MPU(CAN) Series Genset Controller Version: 1.1 2016-11-03 Page 63 of 77

13 INSTALLATION

Controller is panel built-in design; it is fixed by clips when installed. The controller’s overall

dimensions and cutout dimensions for panel, please refers to as following,

Battery Voltage Input

NOTE:

HGM93XXMPU(CAN) series controller can suit for widely range of battery voltage

DC(8~35)V. Negative of battery must be connected with the engine shell. The diameter of

wire which from power supply to battery must be over 2.5mm

. If floating charge configured,

please firstly connect output wires of charger to battery’s positive and negative directly, then,

connect wires from battery’s positive and negative to controller’s positive and negative input

ports in order to prevent charge disturbing the controller’s normal working.

Speed Sensor Input

NOTE:

Speed sensor is the magnetic equipment which be installed in starter and for

detecting flywheel teeth. Its connection wires to controller should apply for 2 cores shielding

line. The shielding layer should connect to No. 16 terminal in controller while another side is

hanging in air. The else two signal wires are connected to No.17 and No.18 terminals in

controller. The output voltage of speed sensor should be within AC(1~24)V (effective value)

during the full speed. AC12V is recommended (in rated speed). When install the speed

sensor, let the sensor is spun to contacting flywheel first, then, port out 1/3 lap, and lock the

nuts of sensor at last.

Output And Expand Relays

CAUTION:

All outputs of controller are relay contact output type. If need to expand the

relays, please add freewheel diode to both ends of expand relay’s coils (when coils of relay

has DC current) or, increase resistance-capacitance return circuit (when coils of relay has AC

Содержание HGM 9310CAN Series














































































Результаты поиска

Содержание HGM 9310CAN Series

Отзывы:

Похожие инструкции для HGM 9310CAN Series

Бренды по названию

Популярные бренды

Smartgen HGM 9310CAN Series, Руководство пользователя

Результаты поиска

Содержание HGM 9310CAN Series

Отзывы:

Похожие инструкции для HGM 9310CAN Series

Бренды по названию

Популярные бренды