Smartgen HGM 9310CAN Series Скачать руководство пользователя страница 61

Страница: 61 / 77

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER

HGM93XX MPU(CAN) Series Genset Controller Version: 1.1 2016-11-03 Page 61 of 77

11 COMMISSIONING

Please make the under procedures checking before commissioning,

1. Ensure all the connections are correct and wires diameter is suitable.

2. Ensure that the controller DC power has fuse, controller‘s positive and negative

connected to start battery are correct.

3. Emergence stop must be connected with positive of start battery via scram button’s

normal close point and fuse.

4. Take proper action to prevent engine to crank disconnect (e. g. Remove the connection

wire of fuel valve). If checking is OK, make the start battery power on; choose manual

mode and controller will executive routine.

5. Set controller under manual mode, press “start” button, genset will start. After the setting

times as setting, controller will send signal of Start Fail; then press “stop” to reset

controller.

6. Recover the action of stop engine start (e. g. Connect wire of fuel valve), press start

button again, genset will start. If everything goes well, genset will normal run after idle

running (if idle run be set). During this time, please watch for engine’s running situations

and AC generator’s voltage and frequency. If abnormal, stop genset running and check

all wires connection according to this manual.

7. Select the

AUTO

mode from controller’s panel, connect mains signal. After the mains

normal delay, controller will transfer ATS (if fitted) into mains load. After cooling time,

controller will stop genset and make it into “at rest” mode until there is abnormal of mains.

8. When mains is abnormal again, genset will be started automatically and into normal

running, then controller send signal to making generator switch on, and control the ATS

as generator load. If not like this, please check ATS wires connection of control part

according to this manual.

9. If there is any other question, please contact Smartgen’s service.

Содержание HGM 9310CAN Series














































































Результаты поиска

Содержание HGM 9310CAN Series

Отзывы:

Похожие инструкции для HGM 9310CAN Series

Бренды по названию

Популярные бренды

Smartgen HGM 9310CAN Series, Руководство пользователя

Результаты поиска

Содержание HGM 9310CAN Series

Отзывы:

Похожие инструкции для HGM 9310CAN Series

Бренды по названию

Популярные бренды