Smartgen HGM 9310CAN Series Скачать руководство пользователя страница 46

Страница: 46 / 77

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER

HGM93XX MPU(CAN) Series Genset Controller Version: 1.1 2016-11-03 Page 46 of 77

8.2 ENABLE DEFINITION OF PROGRAMMABLE OUTPUT PORTS

Form 2

No.

Type

Description

Not Used

Custom Period 1

Details of function description please see the following.

Custom Period 2

Custom Period 3

Custom Period 4

Custom Period 5

Custom Period 6

Custom Combined 1

Custom Combined 2

Custom Combined 3

Custom Combined 4

Custom Combined 5

Custom Combined 6

Reserved

Gas Choke On

Action while cranking. Action time is as pre-seted.

Gas Ignition

Action when genset starting, and disconnect when
engine stopped.

Air Flap

Action when over speed shutdown and emergence stop.
It can close the air inflow to stop the engine as soon as
possible.

Audible Alarm

Action when warning, shutdown, trips. Can be
connected annunciator externally. When “alarm mute”
configurable input port is active, it can remove the
alarm.

Louver Control

Action when genset is cranking and disconnect when
genset stopped completely.

Fuel Pump Control

It is controlled by fuel pump of level sensor’s limited
threshold.

Heater Control

It is controlled by heating of temperature sensor’s
limited threshold.

Cooler Control

It is controlled by cooler of temperature sensor’s limited
threshold.

Oil Pre-supply Output

Action from “crank on” to “safety on”.

Excite Generator

Output in start period. If there is no generator frequency
during normal running, it outputs for 2 seconds again.

Pre-Lubricate

Actions in period of pre-heating to safety run.

Remote PC Output

This port is controlled by communication (PC).

GSM Power

Power for GSM module (GSM module is reset when
GSM communication failed).

Reserved

Содержание HGM 9310CAN Series














































































Результаты поиска

Содержание HGM 9310CAN Series

Отзывы:

Бренды по названию

Популярные бренды

Smartgen HGM 9310CAN Series, Руководство пользователя

Результаты поиска

Содержание HGM 9310CAN Series

Отзывы:

Бренды по названию

Популярные бренды