Smartgen HGM 9310CAN Series Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 77

background image

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER

HGM93XX MPU(CAN) Series Genset Controller Version: 1.1 2016-11-03 Page 77 of 77

16 FAULT FINDING

Symptoms

Possible Solutions

Controller no response with
power.

Check starting batteries;
Check controller connection wirings;
Check DC fuse.

Genset shutdown

Check the water/cylinder temperature is too high or not;
Check the genset AC voltage;
Check DC fuse.

Controller emergency stop

Check emergence stop button is correct or not;
Check whether the starting battery positive is connected
with the emergency stop input;
Check whether the circuit is open.

Low oil pressure alarm after
crank disconnect

Check the oil pressure sensor and its connections.

High water temp. alarm after
crank disconnect

Check the temperature sensor and its connections.

Shutdown Alarm in running

Check related switch and its connections according to the
information on LCD;
Check auxiliary input ports.

Fail to start

Check fuel oil circuit and its connections;
Check starting batteries;
Check speed sensor and its connections;
Refer to engine manual.

Starter no response

Check starter connections;
Check starting batteries.

Genset running while ATS
not transfer

Check ATS;
Check the connections between ATS and controllers.

RS485 communication is
abnormal

Check connections;
Check COM port setting is correct or not;
Check RS485’s connections of A and B is reverse connect
or not;
Check RS485 transfer model whether damage or not;
Check communication port of PC whether damage or not.

ECU communication failed

Check connections of CAN high and low polarity;

Check if correctly connected of 120Ω r

esister;

Check if type of engine correct;
Check if connections from controller to engine and output
ports setting are correct.

ECU warning or shutdown

Get information from LCD of alarm page;
If there is detailed alarm, check engine according to
description. If not, please refer to engine manual according
to SPN alarm code.

«
...
75
76
77

Содержание HGM 9310CAN Series














































































Отзывы:

Нет отзывов

Похожие инструкции для HGM 9310CAN Series

Concord express

Бренд: GE Страницы: 3

Бренд: Walchem Страницы: 10

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

ecomat 100 R 360

Бренд: IFM Electronic Страницы: 16

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 11

Бренд: IFM Electronic Страницы: 23

Бренд: C&C Страницы: 17

Бренд: Parker Страницы: 16

Бренд: ZKTeco Страницы: 2

MT600iWP Series

Бренд: weintek Страницы: 2

Бренд: WAC Страницы: 5

Бренд: IR-Tec Страницы: 14

Бренд: Cardin Elettronica Страницы: 56

Бренд: Blucave Страницы: 2

Бренд: SMC Networks Страницы: 31

Бренд: FADAL Страницы: 2

Бренд: GCE Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды