Smartgen HGM 9310CAN Series Скачать руководство пользователя страница 59

Страница: 59 / 77

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER

HGM93XX MPU(CAN) Series Genset Controller Version: 1.1 2016-11-03 Page 59 of 77

9 PARAMETERS SETTING

In HGM9310MPU(CAN) controller, there are no items of mains in setting and also no mains

items in configurable ports of input/output.

CAUTION:

Please change the controller parameters when generator is in standby mode

only (e. g. Crank disconnect conditions selection, auxiliary input, auxiliary output, various

delay), otherwise, shutdown and other abnormal conditions may happen.

NOTE:

Maximum set value must over minimum set value in case that the condition of too

high as well as too low will happen.

NOTE:

When setting the warning alarm, please set the correct return value; otherwise,

maybe there is abnormal alarm. When setting the maximum value, the return value must less

than set value; When setting the minimum value, the return value must over set value.

NOTE:

Please set the generator frequency value as low as possible when cranking, in

order to make the starter be separated quickly as soon as crank disconnect.

NOTE:

Auxiliary input could not be set as same items; otherwise, there are abnormal

functions. However, the auxiliary output can be set as same items.

Содержание HGM 9310CAN Series














































































Результаты поиска

Содержание HGM 9310CAN Series

Отзывы:

Похожие инструкции для HGM 9310CAN Series

Бренды по названию

Популярные бренды

Smartgen HGM 9310CAN Series, Руководство пользователя

Результаты поиска

Содержание HGM 9310CAN Series

Отзывы:

Похожие инструкции для HGM 9310CAN Series

Бренды по названию

Популярные бренды