7 - 24
Figure 30. Fuel Level Sensor Assembly
A. Sensor Assembly
G. Nuts
B. Float
H. Washer
C. Sensor
I. Terminals
D. Screw
J. Fuel Tank
E.
Lockwasher
K. Gasket
F.
Wires
FUEL TANK LEVEL SENSOR
The fuel tank level sensor is located inside the fuel tank.
It is a float type that is submerged into the tank. The float
is on the end of an arm and, as the arm moves up and
down, it changes the resistance, which in turn changes
the voltage level of the fuel level signal to the instrument
panel.
A general testing procedure for the fuel level sensor is
provided in the Component Tests section.
1. Disconnect and secure the negative battery cable
(see Section 6, COMMON SERVICE PROCE-
DURES).
2. Remove the seat deck and rear plastic guard, (see
Section 15, SEAT DECK SERVICE).
3. Remove the nuts (G, Figure 30) and washer (H) hold-
ing the wires (F) to the terminals (I). Label the wires
for easy reconnection.
4. Remove all screws (D) and lockwashers (E) holding
the sensor assembly (A) on the tank (J) and carefully
pull sensor out. Replace gasket (K) if damaged.
5. Reinstall fuel tank level sensor and seat deck in
reverse order of this instruction.
B
C
A
K
J
H
E
D
G
F
I
7 Electrical System Service
Location and Replacement
Figure 31. Seat Switch Safety System
A. Coolant Sensor
B. Sensor Wire
IGNITION COIL (MAGNETO)
Refer to the engine manufacturer’s manual for specific
information regarding engine component testing and
replacement.
OIL PRESSURE SENSOR
All models contain an oil pressure sensor (sender) which
is located on the engine.
Refer to the engine manufacturer’s manual for specific
information regarding engine component testing and
replacement.
If after replacing the oil sensor on the engine, the indica-
tor is still malfunctioning, replace the instrument panel.
A
COOLANT TEMPERATURE SENSOR (LIQUID-COOLED
MODELS ONLY)
For the 20 HP Liquid-Cooled Models, refer to the manu-
facturer’s instructions for service procedures and
replacement parts
24.5 HP Diesel Model.
1. Disconnect and secure the negative battery cable,
(see Section 6, COMMON SERVICE PROCE-
DURES).
2. Lift the hood to gain access to the engine. The
coolant temperature sensor (A, Figure 31) is located
in the water pump housing and can be accessed from
the left side of the engine as viewed from the opera-
tors seat.
3. Remove the sensor wire (B) from the sensor (A) by
removing the hex nut and lockwasher.
NOTE: Since the sensor is brass, which is a softer metal,
use extreme caution in removing the sensor to prevent it
from being sheared off.
NOTE: If inaccurate coolant temperature indications on
the temperature gauge still remain after the sensor is
replaced, replace the instrument panel.
B
Not
for
Reproduction
Содержание AGCO Allis 2000 Series
