Siemens SINAMICS S220 Скачать руководство пользователя страница 34

Страница: 34 / 156

3.4.2

Overview of Smart Line Modules

Line Modules generate a DC voltage from the connected line voltage that is used to power the
Motor Modules.

All 16 kW and 24 kW Smart Line Modules have DRIVE-CLiQ interfaces for communication with
the Control Unit.

Figure 3-2

Overview of 16 kW and 24 kW Smart Line Modules

General characteristics of the Line Modules

• Supply voltage 3 AC 380 V to 480 V, 50/60 Hz

• Suitable for TN, TT, and IT supply systems

• Internal air cooling

• Short-circuit/ground-fault-proof during the precharge phase

• Integrated DC link and electronics current busbar connection

• LEDs for indicating statuses and for diagnostics

Characteristics of the Smart Line Modules

• Unregulated DC link voltage

• Energy recovery capability

• Block-type line currents in the energy recovery direction

System overview
3.4 S220 components and system data

Booksize power units

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

Содержание SINAMICS S220





























































































































































Результаты поиска

Содержание SINAMICS S220

Отзывы:

Siemens SINAMICS S220, Руководство по эксплуатации оборудования, Страница: 34 / 156

Результаты поиска

Содержание SINAMICS S220

Отзывы: