Siemens SINAMICS S220 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 156

Siemens SINAMICS S220 Скачать руководство пользователя страница 32

• North American market

SINAMICS S devices provided with one of the test symbols displayed fulfill the requirements
stipulated for the North American market as a component of drive applications.
You can find the relevant certificates on the internet pages of the certifying body (

iq.ulprospector.com

).

• Australia and New Zealand (RCM formerly C-Tick)

SINAMICS S devices showing the test symbols fulfill the EMC requirements for Australia and
New Zealand.

• Quality systems

Siemens AG employs a Quality Management System that meets the requirements of ISO
9001 and ISO 14001.

Not relevant standards

China Compulsory Certification
SINAMICS S devices do not fall in the area of validity of the China Compulsory Certification (CCC).

EMC limit values in South Korea

The EMC limit values to be complied with for Korea correspond to the limit values of the EMC
product standard for variable-speed electric drives IEC 61800-3, category C2 or CISPR 11 / KN11.
By implementing appropriate additional measures, the limit values according to category C2 or
limit value class A, Group 1, are observed. Further, additional measures may be required, such
as using an additional radio interference suppression filter (EMC filter).
The measures for EMC-compliant design of the system are described in detail in this manual and
in the EMC Installation Guideline Configuration Manual.
The final statement regarding compliance with the standard is given by the respective label
attached to the individual unit.

System overview
3.3 Directives, standards, certificates

Booksize power units

30

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

«
...
30
31
32
33
34
...
»

Содержание SINAMICS S220





























































































































































Отзывы:

Нет отзывов