Siemens SINAMICS S220 Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 156

Siemens SINAMICS S220 Скачать руководство пользователя страница 148

9.2

Replacing the fan

WARNING

Electric shock when live parts are touched

Before replacing the fan, you must switch off the power supplies (400 V AC and 24 V DC). A
hazardous voltage is still present for up to five minutes after the power supply has been
switched off.

Contact with live parts can result in death or serious injury.
• Remove the device cover or the fan cover only after a certain time.
• Check for zero voltage before removing the component.

Note

When replacing the fan, you must observe the ESD regulations.

Only qualified personnel are permitted to install spare parts.

The fan modules of Smart Line Modules can be ordered as replacement parts.

Smart Line Modules have an operating hours counter (p0251) and issue a message (A30042)
once the maximum operating time has been reached.

Note
No ventilation if wrong fan module is used

S220 Smart Line Modules are only equipped with 12 V fans. It is not permissible that you use fan
modules with a rated fan voltage of 24 V.
• When replacing the fan always use the associated fan module.

Table 9-1

Fan modules for replacing a fan

Smart Line Modules

Fan modules

Width

Rated power

Article number

Rated fan voltage

100 mm

16 kW / 24 kW

6SL5166-0AD00-0AA0

12 V

Required tools:

• Torx screwdriver T20

• Slotted screwdriver 0.8 x 5.5 mm

Service and maintenance
9.2 Replacing the fan

Booksize power units

146

Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

«
...
146
147
148
149
150
...
»

Содержание SINAMICS S220





























































































































































Отзывы:

Нет отзывов