Siemens SINAMICS S220 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 156

Siemens SINAMICS S220 Скачать руководство пользователя страница 129

Using an external 24 V power supply

SELV or PELV power supplies can be used for the external 24 V volt supply, e.g. SITOP. The ground
potential must be connected to the protective conductor system at the power supply output
(PELV). The cross-section of this connection must be at least as large as the cross-section of the
24 V conductors.
A 24 V terminal adapter must be connected to the component for the infeed. The external power
supply should be located very close to the load.

)

0

;

9

0RWRU

0RGXOH

0RWRU

0RGXOH

/LQH

0RGXOH

&8

)

0

'&9

0

'&9

Figure 8-3

Example of a 24 V supply via an external power supply

8.8.3

Overcurrent protection

The cables on the primary and secondary sides of the 24 V power supply must be protected
against overcurrent.

Primary side protection must be implemented according to the manufacturer's instructions.

Secondary side protection depends on the prevailing situation. Note the following points:

• Load levels as a result of connected loads, including the rated diversity factor depending on

the operation of the machine

• Current-carrying capacity of the conductors used and cables in normal and short-circuit

conditions

• Ambient temperature

• Cable bundling (laying cables in a common duct)

• Type of cable routing

EN 60204-1, Section 14, can be used to determine the overcurrent protective devices.

Control cabinet design and EMC booksize

8.8 24 V DC supply voltage

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

127

«
...
127
128
129
130
131
...
»

Содержание SINAMICS S220





























































































































































Отзывы:

Нет отзывов