Siemens SINAMICS S220 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 156

Siemens SINAMICS S220 Скачать руководство пользователя страница 105

7.2.1

Electrical connection

Connection to the DC link busbars

The SITOP PSU400M is connected to the DC link via the "+" and "-" terminals using a DC link
adapter.

Table 7-2

INPUT DC: Input-side connection of the SITOP PSU400M at the DC link

INOUT DC

Terminal

Technical specifications

+ positive

Screw terminals:
DC inputs "+" and "-", PE:

- negative

Connectable cable cross-sections

0.05 - 4 (2.5) mm² solid (finely stranded) (AWG 24 ... 12)

Tool

Cross-tip screwdriver (0.6 x 3.5)

Tightening torque

0.5 - 0.6 Nm (lbf in)

Note
Connecting the protective conductor

The SITOP PSU400M power supply has two protective conductor connections. Do not connect
the protective conductor to the input (not even capacitively). The cross-sections of the protective
conductor connections and the DC link connecting cable must be identical.

Table 7-3

Compatible DC link adapter

DC link adapter

6SL3162-2BD00-0AA0

Rated current

43 A

Terminal

DCP

Supply voltage: 495 ... 720 VDC

DCN

Information about connecting the DC link adapter to Smart Line Modules is provided in Chapter
"DC link adapters (Page 82)".

DC link components

7.2 SITOP PSU400M

Booksize power units
Equipment Manual, 01/2022, 6SL3097-6AC30-0BP0

103

«
...
103
104
105
106
107
...
»

Содержание SINAMICS S220





























































































































































Отзывы:

Нет отзывов