Siemens SIMOCODE 3UF Скачать руководство пользователя страница 97

Страница: 97 / 172

Standard Functions

12.7 Safety Oriented Tripping

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

12.7

Safety Oriented Tripping

12.7.1

Safety-oriented Tripping

Note
Please note that the information made available for further processing is in the form of non-

safety-oriented signals.

Note
Please note that the "Safe tripping" function block is not a safety-oriented tripping function.

The DM-F Local safety function is determined by the DIP switch setting on the module only.

The DM-F PROFIsafe safety function is performed by the failsafe program in the F-CPU.

Further information: See System Manual.
A total of 1 "Safe tripping" function block is available for SAFETY (Local) or PROFIsafe.
The "DM-F Local safe tripping" function block consists of 3 sockets:

●

Event - DM-F LOCAL ok: The DM-F Local is ready for operation.

●

Event - Safe tripping: A safety-oriented tripping has been carried out.

●

Status - Enabling circuit closed: The enabling circuit is closed.

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации, Страница: 97 / 172

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы: