Siemens SIMOCODE 3UF Скачать руководство пользователя страница 127

Страница: 127 / 172

Logic Modules

13.9 Calculation Modules

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

127

13.9

Calculation Modules

13.9.1

Calculation Modules

Calculation Modules 1 and 2
Both the Calculator 1 and Calculator 2 logic modules integrated in Basic Unit 2 contain the

standard calculation modes and enable all analog values that occur in SIMOCODE pro to be

adapted, calculated and converted, e.g.

●

Conversion of the measured temperatures from K (Kelvin) to °F or °C

●

Conversion of the motor current from % to A

●

Conversion of the 0/4 - 20 mA signals of the Analog Module directly into fill levels,

pressures and flow rates.

The analog value (2 Byte/1 Word) present at the analog socket is calculated using a defined

formula and using freely-selectable parameters (counters, denominators, operators, offsets).

The result of the calculation is output as an analog value at the analog socket of the logic

module (2 Bytes/1 Word) for further processing.
Each Calculator consists of:

●

1 analog plug (Calculator 1) or two analog plugs (Calculator 2)

●

1 logic component

●

1 analog socket (Calculation Module Output).

Formula Calculator 1

Formulas Calculator 2

●

Operation mode 1: Both inputs of type word.

●

Operation mode 2: Inputs 1 and 2 correspond to a D-word input.

●

Offset value range: - 2147483648 to 2147483647, increment 1.

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации, Страница: 127 / 172

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы: