Siemens SIMOCODE 3UF Скачать руководство пользователя страница 96

Страница: 96 / 172

Standard Functions

12.6 Emergency Start

SIMOCODE PRO V PN FDI

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

12.6

Emergency Start

The emergency start deletes the thermal memory from SIMOCODE pro each time it is

activated. This enables immediate restarting of the motor after an overload trip. This function

can be used to:

●

Enable a reset and start up the motor again immediately after an overload trip.

●

Delete the thermal memory (motor model) during operation, if required.

Note
Frequent emergency starts may result in thermal overloading of the motor.

An emergency start is carried out via the plug of the function block. To do this, the input

(plug) of the function block must be connected to any socket (e.g. device inputs, control bits

from PROFINET, etc.).
The Emergency Start function block consists of:

●

1 plug

●

1 "Status - Emergency Start Executed" socket. This is set when the emergency start is

carried out.

Overall, there is 1 Emergency Start function block for BU1 and BU2.

Settings Emergency Start

Control of the Emergency Start function block from any signal (any sockets, e.g. device

inputs, control bits from PROFINET, etc.).

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации, Страница: 96 / 172

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы: