Siemens SIMOCODE 3UF Скачать руководство пользователя страница 79

Страница: 79 / 172

Outputs

11.5 Analog Module Outputs

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

Application examples

●

Controlling the motor contactor in the motor feeder:

You can e.g. define which relay output is used for controlling the motor contactor in the

motor feeder. For this, connect the desired relay output to the respective "QE" contactor

control of the control function.

●

Lamp control for displaying operating states:

You can e.g. define which relay outputs are to be used for controlling the lamps/LEDs

displaying operating states of the motor (FAULT, ON, OFF, FAST, SLOW...).

For this, connect the desired relay output to the respective "QE..." Lamp Control of the

control function.

●

Transfer of any other information, status information, warnings, faults, etc. to the relay

outputs.

Settings Digital Module 2 Outputs

Control of the DM2 outputs function block with any signal (any sockets, e.g. device inputs,

control bits from PROFINET, etc. usually from the QE contactor controls).

11.5

Analog Module Outputs

You can use analog modules 1 and 2 to expand basic unit 3 with one analog input each. The

corresponding function blocks "AM1 Output" and "AM2 Output" (in conjunction with

SIMOCODE pro V PN basic unit only) allow every analog value (2 bytes/1 word) in

SIMOCODE pro to be output as a 0/4 A - 20 mA signal, for example, on a connected pointer

instrument. By activating the function block via the "assigned analog output value" plug with

any integer value between 0 and 65535, an equivalent analog signal of 0 to 20 mA or 4 to 20

mA will be sent to the output terminals of the Analog Module.

Note
The AM1 Output and AM2 Output function blocks can only be used if the respective analog

module (AM) is connected and configured in the device configuration!

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации, Страница: 79 / 172

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы: