Siemens SIMOCODE 3UF Скачать руководство пользователя страница 55

Страница: 55 / 172

Monitoring Functions

9.5 Active Power

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

Response at Warning Level

Here you can set how SIMOCODE pro should respond if the set Warning Level is undershot:

Response

Warning level

Disabled

Signaling

Warning

Tripping

Range

0 to 25.5 s

Preset

0.5 s

9.5

Active Power

9.5.1

Active Power

SIMOCODE pro can indirectly monitor the state of a device or system via the Active Power.

For example, by monitoring the Active Power of a pump motor, conclusions can be drawn

from the Active Power level about the flow rate or fluid fill levels. The active power curve of a

motor is a precise reflection of its actual load across the entire range. Excess load results in

increased wear of the motor and, thus, may lead to premature motor failure. Insufficient

active power can, for example, be a sign of non-load motor operation.
SIMOCODE pro supports 2-phase monitoring of the Active Power for freely-selectable upper

and lower current limits. The response of SIMOCODE pro when a pre-warning or trip Level

has been reached can be freely parameterized and delayed.
Active Power is measured via current/voltage measuring modules.

Trip level (CiR), Warning level (CiR)

With Active Power Monitoring, you can parameterize two different Response Levels (trip

level/warning level) for the upper and lower limit.

Trip level:

•

P> (upper limit)

0 to 4294967.295 kW

•

P< (lower limit)

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды