Siemens SIMOCODE 3UF Скачать руководство пользователя страница 57

Страница: 57 / 172

Monitoring Functions

9.5 Active Power

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

9.5.2

P> (upper limit)

Monitoring Active Power P> (upper limit)

SIMOCODE pro can indirectly monitor the state of a device or system via the Active Power.

For example, by monitoring the Active Power of a pump motor, conclusions can be drawn

from the Active Power level about the flow rate or fluid fill levels. The active power curve of a

motor is a precise reflection of its actual load across the entire range. Excess load results in

increased wear of the motor and, thus, may lead to premature motor failure.
SIMOCODE pro supports 2-phase monitoring of the Active Power for freely-selectable upper

current limits. The response of SIMOCODE pro when a pre-warning or trip Level has been

reached can be freely parameterized and delayed.
Active Power is measured via current/voltage measuring modules.

Trip level (CiR), warning level (CiR)

With Active Power Monitoring, you can parameterize two different response levels (trip

level/warning level) for the upper limit:

●

Trip level: 0 to 4294967.295 kW

●

Warning level: 0 to 4294967.295 kW.

Trip level and warning level activity

The trip level/warning level is only effective when the motor is running, the start-up

procedure has been completed and there is no Test Position Feedback (TPF) (run+).

Response, Delay (CiR) at trip level

Here you can set:

●

how SIMOCODE pro should respond if the set trip level is overshot

●

the delay time.

Response

Trip level

Disabled

Signaling

Warning

Tripping

Delay

0 to 25.5 s

Preset

0.5 s

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации, Страница: 57 / 172

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы: