Siemens SIMOCODE 3UF Скачать руководство пользователя страница 32

Страница: 32 / 172

Motor Control

8.2 Control Station

SIMOCODE PRO V PN FDI

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

8.2.2

Operation Mode Selector

You can use the control stations either individually or in combination. There are four different

operating modes you can switch between:

●

Local 1

●

Local 2

●

Local 3

●

Remote/Automatic: In this mode of operation, the communication must be carried out via

PLC.

Not all control stations are usually connected. If more than one control station (e.g. local and

PLC/PCS) is connected, it makes sense and is also mandatory to operate the control

stations selectively. 4 operating modes are provided for this purpose which can be selected

via 2 control signals (mode selectors). For each individual control station in every operating

mode, it can be stipulated if "ON commands" and/or "OFF commands" are to be used. The

operating modes are so controlled that only one operating mode is active at any one time.
Example: There are 3 modes of operation in a system:

Mode of operation

Description

Key-operated switch operation,e.g.

local 1

Only local control entries are admissible!
All other control stations are locked

Manual operation, e.g. local 3

Only operator panel control commands and local

control commands can be issued.

Remote operation, e.g.

remote/automatic

Only PLC/DCS control commands are permitted;

locally, only OFF commands are permitted

The key-operated Switch must be read in via an input to select these operating modes. The

Remote Switching operation should be controlled via the bus. The Key-operated Switching

operation has priority over all other operating modes.
The S1/S2 mode selectors are used to switch between the operating modes "Local 1", "Local

2", "Local 3" and "Remote/Automatic".

The S1 and S2 plugs must be connected to arbitrary sockets (e.g. device inputs, control bits

from PROFINET, etc.) for this.
The following table shows the operating modes, depending on the signal status of the S1

and S2 mode selectors:

Mode of operation

Input

Local 1

Local 2

Local 3

Remote/automatic

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды