Siemens SIMOCODE 3UF Скачать руководство пользователя страница 37

Страница: 37 / 172

Motor Control

8.3 Control Function

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

8.3.2

Operating Mode

Parameter

Description

Non-maintained command mode

•

Deactivated:

The control command on the corresponding input of

the control stations "ON <, ON <<, ON >,ON >>" is

saved. It can only be revoked by an "OFF" control

command from the corresponding control station.

The auxiliary contact for locking the contactor is no

longer necessary. Motor feeders are usually operated

in locking mode. Locking is preset.

•

Activated:

Depending on the control function chosen, the Non-

maintained command mode affects the plugs of all

control stations "ON <, ON <<, ON >, ON >>".A

control command is only effective as long as there is

a "high signal".

Saving change-over Command

•

Deactivated:

Commands for switching from one direction of

rotation/rotational speed to the other are

implemented with a previous "OFF" and after the

interlocking time/change-over pause has elapsed.

This setting is usually used and is preset.

•

Activated:

Commands for switching from one direction of

rotation/rotational speed to the other are

implemented without a previous "OFF" and after the

interlocking time/change-over pause has elapsed. If

the selected direction/speed cannot be executed

immediately due to a parameterized interlocking

time/change-over pause, the selection is signalized

by flickering QLE displays. Your selection can be

cancelled at any time with "OFF".

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды