Siemens SIMOCODE 3UF Скачать руководство пользователя страница 27

Страница: 27 / 172

Motor Protection

7.1 Overload Protection

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

Response at Pre-Warning Level (I>115%I

)

The response of SIMOCODE pro can be additionally adjusted in case of overload (disabled,

signaling, warning).

Delay pre-warning (CiR)

The "delay" parameter (default: 0.5 s) is used to determine the interval during which the pre-

warning level (1.15 x I

) must be constantly exceeded before SIMOCODE pro executes the

desired response. Otherwise, there is no reaction.
In case of phase failure or unbalance > 50 %, this pre-warning is already issued at approx.

0.85 x Ie.

Reset

If the "Reset" parameter is set to "Auto", the "Overload", "Ov unbalance" and

"Thermistor" faults are acknowledged automatically

●

if the cooling down period has expired

●

if the thermistor value has decreased to the resetting value according to specification.

If the "Reset" parameter is set to "Manual", the errors must be acknowledged by a reset

signal:

●

"Reset" button on the basic unit

●

"Reset" button on the operator panel

●

"Reset" standard functions. For this reason, the "Reset - input" inputs (plugs) must be

connected to the corresponding sockets, e.g. using reset via the bus.

Reset:

Manual, Auto

Note
The "Auto reset" mode of operation may not be used in applications in which an unexpected

restart of the motor can lead to damage to persons or objects.

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды