Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 57

Страница: 57 / 82

Connection

6.3 Ethernet

SCALANCE WxM766
Operating Instructions, 03/2022, C79000-G8976-C617-03

Power over Ethernet (PoE)

Note

Before you pull a plug via which the device is supplied with power using PoE, disable the

relevant PoE power supply.

Note
No power sourcing equipment (PSE)

The SCALANCE WxM766-1 devices cannot be used as PoE power supply for other

devices.

6.3

Ethernet

For connection to Industrial Ethernet at 10/100/1000 Mbps, the device has an M12

interface: X-coded, 8-pin.
The power can also be supplied via this interface (Power over Ethernet)

Position and pin assignment

Pin

Assignment

D0+

D0-

D1+

D1-

D3+

D3-

D2-

D2+

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды