Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 51

Страница: 51 / 82

Connection

6.1 Safety when connecting up

SCALANCE WxM766
Operating Instructions, 03/2022, C79000-G8976-C617-03

NOTICE
Damage to the device due to potential differences

To fully eliminate the influence of electromagnetic interference, the device must be

grounded. There must be no potential difference between the following parts, otherwise

the device or other connected device could be severely damaged:
•

Housing of the SCALANCE W device and the ground potential of the antenna.

•

Housing of the SCALANCE W device and the ground potential of a device connected

over Ethernet.

•

Housing of the SCALANCE W device and the shield contact of the connected

Ethernet cable.

Connect both grounds to the same foundation earth or use an equipotential bonding

cable.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

Do not connect or disconnect cables to or from the device when a flammable or

combustible atmosphere is present.

WARNING

EXPLOSION HAZARD

Do not press the reset button if there is a potentially explosive atmosphere.

WARNING

Unsuitable cables or connectors

Risk of explosion in hazardous areas
•

Only use connectors that meet the requirements of the relevant type of protection.

•

If necessary, tighten the connector screw connections, device fastening screws,

grounding screws, etc. according to the specified torques.

•

Close unused cable openings for electrical connections.

•

Check the cables for a tight fit after installation.

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды