Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 29

Страница: 29 / 82

Description of the device

4.5 Accessories

SCALANCE WxM766
Operating Instructions, 03/2022, C79000-G8976-C617-03

4.5.6.5

Antennas

Note

When you select an antenna, keep in mind:
•

The antennas with national approval for your device You will find further information

on this on the Internet pages of Siemens Industry Online Support

(

https://support.industry.siemens.com/cs/de/en/view/109802595

•

The country-specific and channel-dependent maximum permissible antenna gain You

will find further information on this in the reference document "Approvals SCALANCE

W700 802.11ax" on the Internet pages of the Siemens Industry Online Support

(

https://www.siemens.com/wireless-approvals

Type

Properties

Article number

ANT792-4DN

RCoax helical antenna, circular

polarization, 4 dBi, 2.4 GHz, N-Connect

female.

6GK5792-4DN00-0AA6

ANT792-6MN

Omni antenna, mast/wall mounting, 6 dBi

2.4 GHz, N-Connect female

6GK5792-6MN00-0AA6

ANT792-8DN

Directional antenna, mast/wall mounting,

14 dBi 2.4 GHz, N-Connect female

6GK5792-8DN00-0AA6

ANT793-6DG

Wide angle antenna, mast/wall mounting,

9 dBi 5 GHz, 2 x N-Connect female

6GK5793-6DG00-0AA0

ANT793-8DJ

Directional antenna, mast/wall mounting,

18 dBi 5 GHz, 2 x N-Connect female

6GK5793-8DJ00-0AA0

ANT793-8DK

Directional antenna, mast/wall mounting,

23 dBi 5 GHz, 2 x N-Connect female

6GK5793-8DK00-0AA0

IWLAN RCoax
ANT793-4MN

RCoax

4 antenna with vertical

polarization for RCoax systems, 6 dBi,

5 GHz, IP65, N-Connector female

6GK5793-4MN00-0AA6

ANT795-4MC

Omnidirectional antenna, 3/5 dBi, 2.4 GHz

and 5 GHz, IP65, N-Connect male for

direct installation on the device, straight

connector.

6GK5795-4MC00-0AA3

ANT795-4MD

Omnidirectional antenna, 3/5 dBi, 2.4 GHz

and 5 GHz, IP65, N-Connect male for

direct installation on the device, 90°

connector.

6GK5795-4MD00-0AA3

ANT795-6DC

Wide angle antenna, mast/wall mounting,

9 dBi 2.4 GHz and 5 GHz, N-Connect

female

6GK5795-6DC00-0AA0

ANT795-6MN

Omni antenna, mounted on roof/vehicle,

6/8 dBi 2.4 GHz and 5 GHz, N-Connect

female

6GK5795-6MN10-0AA6

ANT793-8DL

Directional antenna vertical-horizontal

polarized, 5 GHz, 14dBi, IP66, 2 x N-

Connector female

6GK5793-8DL00-0AA0

ANT793-8DP

Directional antenna, mast/wall mounting,

13 / 13.5 dBi 4.9 GHz and 5 GHz, N-

Connect female

6GK5793-8DP00-0AA0

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды