Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 58

Страница: 58 / 82

Connection

6.4 Antennas

SCALANCE WxM766

Operating Instructions, 03/2022, C79000-G8976-C617-03

Connecting Ethernet ports

Connect the plug and socket. Make sure that they lock in place correctly.

Tighten the knurled screw (torque 1 Nm).

6.4

Antennas

The SCALANCE WxM766-1 has two antenna connectors of the N-Connector female type.

Figure 6-1 Antenna connectors

①

Antenna connector R1 A1

②

Antenna connector R1 A2

Procedure

Follow the steps below to connect a cable for an external antenna:
1.

Remove the protective cap from the affected N-Connector on the device.

Note
Keep the protective caps

Keep the removed protective caps for later use.

You can connect an external antenna directly to the device or connect it with a flexible

connecting cable.
Place the antenna plug or the flexible connecting cable on the antenna connector and

tighten the sleeve nut of the plug on the antenna connector (wrench SW19, torque

1.7 Nm).

An antenna must always be connected to R1 A1

①

. You can find additional information

on configuration of antennas in the WBM / CLI.

Screw a terminating resistor onto the unused antenna connector.

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды