Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 40

Страница: 40 / 82

Assembly and disassembly

5.2 Types of installation

SCALANCE WxM766

Operating Instructions, 03/2022, C79000-G8976-C617-03

WARNING

Open equipment

The devices are "open equipment" according to the standard IEC 61010-2-201 or UL

61010-2-201 / CSA C22.2 No. 61010-2-201. To fulfill requirements for safe operation

with regard to mechanical stability, flame retardation, stability, and protection against

contact, the following alternative types of installation are specified:
•

Installation in a suitable cabinet.

•

Installation in a suitable enclosure.

•

Installation in a suitably equipped, enclosed control room.

WARNING

If the temperature at the cable or housing socket or at the branching points of the

cables exceeds 60 °C, special precautions must be taken. If the equipment is operated

at ambient temperatures in excess of 40 °C, only use cables with permitted operating

temperature of at least 80

℃

5.2

Types of installation

Note

The device is only approved for operation in closed rooms. Note the following

environmental conditions.
Antennas, in particular directional antennas, must be mounted in keeping with their

characteristics (refer to the technical specifications of the antenna --> Radiation pattern

diagrams).

For the device the following types of installation are permitted:
•

Wall mounting

•

Ceiling mounting

•

Mounting on VESA bracket 75 x 75 mm

•

Mounting on a DIN rail
The device can be mounted on a DIN rail with

–

A DIN rail mounting adapter

–

A bracket support and the DIN rail mounting adapter for space-saving installation

(90

installation)

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды