Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 34

Страница: 34 / 82

Description of the device

4.8 Configuration License PLUG

SCALANCE WxM766

Operating Instructions, 03/2022, C79000-G8976-C617-03

NOTICE
Inadvertent reset

An inadvertent reset can cause disturbances and failures in a configured network with

further consequences.

4.8

Configuration License PLUG

The CLP (Configuration License PLUG) is used to transfer the configuration of the old

device to the new device when a device is replaced. The CLP is also referred to as PLUG

in the description.
The PLUG is available in the following variants:
•

PLUG Configuration: The exchangeable storage medium only saves the configuration

data of the device.

•

PLUG License: In addition to the configuration data, the exchangeable storage

medium contains a license with which special functions are enabled, e.g. iFeatures.

NOTICE
Loss of the degree of protection

When the cover is not mounted correctly, the device loses its degree of protection IP65

and is not water and dust proof.

Position

The CLP slot is at the bottom of the device enclosure under a cover, see Reset button

(Page 33).

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды