Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 52

Страница: 52 / 82

Connection

6.1 Safety when connecting up

SCALANCE WxM766

Operating Instructions, 03/2022, C79000-G8976-C617-03

WARNING

Lack of equipotential bonding

If there is no equipotential bonding in hazardous areas, there is a risk of explosion due

to equalizing current or ignition sparks.
•

Ensure that equipotential bonding is available for the device.

WARNING

Unprotected cable ends

There is a risk of explosion due to unprotected cable ends in hazardous areas.
•

Protect unused cable ends according to IEC/EN 60079-14.

WARNING

Improper installation of shielded cables

There is a risk of explosion due to equalizing currents between the hazardous area and

the non-hazardous area.
•

Ground shielded cables that cross hazardous areas at one end only.

•

Lay a potential equalization conductor when grounding at both ends.

WARNING

Insufficient isolation of intrinsically safe and non-intrinsically safe circuits

Risk of explosion in hazardous areas
•

When connecting intrinsically safe and non-intrinsically safe circuits, ensure that the

galvanic isolation is performed properly in compliance with local regulations (e.g. IEC

60079-14).

•

Observe the device approvals applicable for your country.

Notes for use in hazardous locations according to ATEX, IECEx, UKEX and CCC Ex

If you use the device under ATEX, IECEx, UKEX or CCC Ex conditions you must also keep

to the following safety instructions in addition to the general safety instructions for

protection against explosion:

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды