Siemens SIMATIC NET 6GK5766-1GE00-3DA0 Скачать руководство пользователя страница 50

Страница: 50 / 82

Connection

6.1 Safety when connecting up

SCALANCE WxM766

Operating Instructions, 03/2022, C79000-G8976-C617-03

Note

The requirements of EN61000-4-5, surge immunity tests on power supply lines, are met

only when a Blitzductor is used with 24 VDC:
BVT AVD 24

article number: 918 422

Manufacturer: DEHN+SÖHNE GmbH+Co.KG, Hans Dehn Str. 1, Postfach 1640, D -

92306 Neumarkt, Germany

Supply voltage

WARNING

Power supply

The device is designed for operation with a directly connectable safety extra-low

voltage (SELV) or protective extra low voltage (PELV) from a limited power source

(LPS).
The power supply therefore needs to meet at least one of the following conditions:
•

Only safety extra low voltages SELV/PELV with limited power source LPS complying

with IEC 62368-1 / EN 62368-1 / VDE 62368-1 may be connected to the power

supply terminals.

•

The power supply unit for the device must meet NEC Class 2 according to the

National Electrical Code (r) (ANSI / NFPA 70).

If the equipment is connected to a redundant power supply (two separate power

supplies), both must meet these requirements.

Grounding

WARNING

Danger to life from overvoltage, fire hazard

When using outdoor antennas, the shared or grounded pin of the circuit must be

connected to the shield of the coaxial cable and to all touchable conductive parts and

circuits. Otherwise, there may be impermissibly high voltages on touchable parts in the

event of a fault.

Содержание SIMATIC NET 6GK5766-1GE00-3DA0



















































































Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды

Siemens SIMATIC NET 6GK5766-1GE00-3DA0, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC NET 6GK5766-1GE00-3DA0

Отзывы:

Похожие инструкции для SIMATIC NET 6GK5766-1GE00-3DA0

Бренды по названию

Популярные бренды