Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 7

Страница: 7 / 142

Contents

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

Contents

Commissioning

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1

Application and Mode of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2

Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3

Ordering Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.1

SICAM P 7KG7750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.2

SICAM P 7KG7755 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.3

Parameterization Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4.1

Device Variant SICAM P 7KG7750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4.2

Device Variant SICAM P 7KG7755 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6

Interface and Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.1

Terminal Assignment SICAM P 7KG7750/55 . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.2

Terminal Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.3

Assignment of the Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.4

Connection Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.4.1

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.4.2

Single-phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.4.3

Three-phase, Three-wire, Balanced. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.4.4

Three-phase, Three-wire, Unbalanced ( 2 I, Aron Circuit) . . . . . . . . . . . . . .

1.6.4.5

Three-phase, Four-wire, Balanced. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.4.6

Three-phase, Four-wire, Unbalanced (Low-voltage System). . . . . . . . . . . .

1.6.4.7

Three-phase, Four-wire, Unbalanced (High-voltage System) . . . . . . . . . . .

1.6.5

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.6

Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6.7

Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

2.1

Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2

Screen Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.1

Screen Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.1.1

3 Measured Values - Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.1.2

6 Measured Values - Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.1.3

U, I and cos f (Phasors) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.1.4

3 Min-Max Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2.2

Status Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Measured Quantities

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1

Measured Quantities - Depend on the Connection Type . . . . . . . . . . . . . . . . . . . .

Содержание SICAM P 7KG7750















































































































































Результаты поиска

Содержание SICAM P 7KG7750

Отзывы:

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 7 / 142

Результаты поиска

Содержание SICAM P 7KG7750

Отзывы: