manualshive.com logo in svg

Siemens SICAM P 7KG7750, Руководство пользователя, Страница: 64 / 142

Поделиться
Скачать
Siemens SICAM P 7KG7750 Скачать руководство пользователя страница 64

4 

4.4 Basic Settings

64

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

4.4.3

Outputs

Here, the user can determine the function of the programmable output contacts (potential-free 
electronic relays). Further contacts can be assigned in devices with I/O modules of the binary 
output or relay output type (option).

Selection

•

Off

Contact has no function

•

SICAM P is on

Contact closed if power supply voltage is present.

•

Energy pulses

If selected, a new window "Energy Pulses" appears.

•

Limit value 1

If selected, a new window "Limit Value 1" appears.

•

Limit value 2

If selected, a new window "Limit Value 2" appears.

•

Limit value 3

If selected, a new window "Limit Value 3" appears.

•

Limit value 4

If selected, a new window "Limit Value 4" appears.

•

Limit value 5

If selected, a new window "Limit Value 5" appears.

•

Limit value 6

If selected, a new window "Limit Value 6" appears.

•

Limit value 7

If selected, a new window "Limit Value 7" appears.

•

Direction of rotation This option allows you to output the rotation direction of the voltage.

•

1: Contact activated; direction of rotation for clockwise display

(phase sequence L1-L2-L3, clockwise rotation)

•

0: Contact deactivated; direction of rotation for anti-clockwise display

(2 phases interchanged, anti-clockwise rotation)

*relay1: limit value1 
*relay2: rotation

<ok
<cancel

Содержание SICAM P 7KG7750















































































































































Отзывы:

Нет отзывов